As an Anderson industrial roof repair contractor, we repair fan curbs, drains, and leaks over production floors on a schedule set with your facility manager.
Anderson industrial roof repair is planned around the plant below. These checks set what gets fixed now and what waits for a shutdown.
| What We Check | Repair During Production | Plan For A Shutdown |
|---|---|---|
| Fan curbs | Reflashing with the fan running nearby | Curb rebuilds needing the fan off |
| Drains | Clearing, resetting rings, resealing | Replacing a drain body over equipment |
| Deck | Work that stays on the membrane | Cutting into the deck over a line |
| Residue | Cleaning and protection pads | Membrane replacement around stacks |
| Leaks | Temporary seal over the source | Permanent repair needing open access |
Plant roofs carry more penetrations and more traffic than most. These six problems bring most calls.
Grease and process residue soften membrane around fans, and curb flashing cracks as the base vibrates. Cleaning, new flashing, and a resistant layer fix it. A resistant cover sheet around the fan base keeps residue off the new seams.
Loose clamping rings and membrane pulled from the drain flange leak straight onto equipment. Reset parts and fresh seals close the gap. Strainers get cleaned and the sump around each drain checked for slope.
Work above can never stop work below. Timing, equipment protection, and contained debris come first on these repairs. Temporary seals cover active areas until a planned shutdown opens the deck.
Stacks, pipe supports, and expansion joints are frequent entry points. Each repair matches the heat and chemicals the area sees. Readings around each entry point show how far water has spread.
Service crews walking to the same units wear paths into the membrane. Walkway pads along those paths protect it. Damaged membrane under the paths gets patched first.
Curbs set too low let ponding water over the flashing. Raising the flashing height keeps it out. New flashing is run up and sealed under the equipment rail.
On a plant, a roof leak is a production problem first.
Repairs planned with the facility manager keep water off machines and product without stopping the line. Temporary seals hold over active areas until the permanent repair fits a planned shutdown.
Drips stop pooling in aisles and under forklifts.
Fan and vent curbs hold their flashing through vibration and heat.
Clear strainers and sealed flanges keep water moving off the roof.
Plant roofs see heat, grease, and chemicals that ordinary repairs do not. Materials get chosen for the exposure.
Around kitchen and process exhaust, PVC or a resistant cover sheet holds up where residue would soften TPO or rubber over time.
Curbs on equipment get flashing raised well above the roof surface so ponding and heavy rain stay below the top edge.
Pads along service paths and protection boards under pipe supports keep traffic and loads from cutting the membrane.
Call and tell us what is under the drip. We will plan a temporary seal that works around your shift schedule.
Plant repairs add a planning step with the facility so the roof work and the floor work never collide.
Fans, stacks, vents, pipe supports, drains, and expansion joints each get checked, with residue and wear marked.
Shift times, lockouts for fan shutdowns, and protection for equipment below get agreed with the facility manager.
The scope separates repairs that fit during production from those that wait for a planned shutdown.
Curbs, drains, and seams get repaired section by section, with debris contained on the roof and nothing cut over a running line.
Photos and a short list of what was fixed and what to watch go to the facility manager for the plant file.
Plant sites often include flat, metal, and leak repairs on nearby buildings.
Blisters, open laps, and ponding on membrane roofs.
Common FixesWet insulation across large areas points to a new roof.
Loose screws, rusted laps, and bent metal flashing.
Common FixesRust through most panels means replacement beats patching.
Ceiling stains traced back to the failed roof detail.
Common FixesLeaks in every section and every rain mean replacement.
Short answers on production, fans, and drains.
Most can. Work that stays on the membrane goes ahead during production, and deck cuts over a line wait for a shutdown.
The facility manager. Shift changes, deliveries, and fan lockouts set the windows we work in.
Grease and process residue soften it, and fan vibration cracks curb flashing. Both get fixed, with protection added around the fan.
Some do, so shutdowns get coordinated with the plant. Reflashing nearby often goes ahead with the fan running.
The strainer and clamping ring come off, the membrane seal is cleaned and reset, and the area around the drain gets sloped to it.
At least each spring and fall, and after big storms. Process dust and leaves clog strainers fast.
Hail marks or punctures, lifted membrane edges, loose trim, debris in drains, and new stains inside. A roof walk soon after finds damage before the next rain.
Owners often use dated photos of each damaged area when they file. We take them during the post-storm roof walk.
Tell us about the plant, the roof, and the shifts. We will plan repairs that keep production running.
